[MOD]--VIRUS--"Full Home-Made" FINISHED

Hello with all

My new MOD is called "virus"

WHY THE MOD VIRUS?

I wanted to create a new style of MOD, more modern, more futuristic one attack of the machines

WHY THE NAME OF VIRUS?

the name of VIRUS, comes from the film fine VIRUS left the Nineties, or a entiter invaded a vessel by the lines of transmission via a satellite, takes the control of data processing, and keep silent all the crew and reconstitutes it semi-men, semi-machines.

The poster of film
It will resemble this one a little


http://forums.bit-tech.net/showthread.php?t=111576

 

"VIRUS" will be enough small for a PC of infiltration, therefore the élements will be micro atx as much as possible, the base will be rather simple to build aluminium and plexi.

Here élements of "VIRUS"

The micro mother chart atx, dd of 160 A left and has right the DVD, the food below

From CM I will build the framework and thus the machine




in any case will not be large 255mm of face limps it

for dissucussion
http://forums.bit-tech.net/showthread.php?t=111576

 

the lower part of VIRUS




Here the face finally the chest


With, an edge

Armour-plates for the chest
With the spacers

Work has the small file for the completion, and always sandpapering à.fond





Here the tete of "VIRUS"

This is the remainder of the éssai of paste PLASTIROC of "SAMURAI" the éssai of face which I had put of dimensioned


I cut with the dremel and aprés a good hour veiled the result







for dissucussion
http://forums.bit-tech.net/showthread.php?t=111576[/QUOTE]

 

Very interesting mod. Looks like you're specialiced in "faced" PCs haha.

I think you would like the new toy of amstrad: http://www.amstrad.com/amsface/index.html

 

Remember the place in the movie where the captain of the ship makes an agreement with the aliens and then try to kill the humans?

 

hello Kumo and Co2


I thank you for your ideas, but "VIRUS" is already to finish, I has just begun my 3 MODS l"O.P.M.TT ".

The face of "VIRUS" is a wink with TERMINATOR FILM CULTE.Au departure "VIRUS" was to be in the form of human, but the prices of the mannequins are trops expensive in France

 

hello everyone

I improve the mask one can the mask
The mask with teeth

fixing of the chart mére and cutting of the arriere



just the plate as well as the clamp holes that my taken more time than envisaged fine extra sandpapering and all the angles too
But also my camera


veiled photographs of the clavicles




Here famous beams with the support for dd or dvd, all and out of aluminum except obviously the beams

 

Here work
The support with its fixing



Work with much of precision, but it is not finished one needs more details
It is necessary that I it reserre

Here the new photographs the ballanciers are almost finished

It misses the clavicles

 

Whoa Mate!!!!

Nice work.

Looking forward to next update.

Regards
BenJ

 

Nice work on Post #4 with the face....

 

Hello

thank you all that has gives me courage for the construction of my mods full home made but for VIRUS you will surprise others

 

Hello with all and Thank you for your messages sympathetic nerves.

I AI The SOLUTION FOR MY CLAVICLES.

Here the Result

The kneecap is adjustable in height with retaining nut


Center aluminum kneecap the spacers make 24mm of longor, with a filtée stem of 70mm and diamétre of 4mm which passes inside with small discs and écroux one-eyed

For my solution of the beams which this levent, I simply curved the clavicles with a thermal decapor


Veiled what that gives.

The hatched parts will be cut out
On the clavicles the green point corresponds has fixing
Veiled the whole with the one-eyed ecroux, the fact that the clavicles either offset and slightly bent causes a rise of the beams of 100mm or of dimensioned or other following as one turns the tete to him

 

One sees well the kinematics of the clavicles in rotation exterieure




A small NEWS, the construction of the low part of "VIRUS"
ATTENTION BOTTOM IS NOT FINISHED

The threaded rods will be used of slides, and adjustment

A 480watt for "VIRUS"
Here a sight of the unit "VIRUS" makes a height of 700mm

 

Man you have way too much time, and way too much skill Your plexi skills drive me mad... well actually, frustrates me... I want them too

 

wow !!

put the gear from a small webcam into that dummy cam and use it for msn !!

 

really nice so far
I like mods that don't follow the standard case design

 

Go hop a small update

Veiled what I did, new the coxis with an end of plexi which was hidden unpleasant OH (le plexi)





Thanks to the burner, now I can fold the plexi
on the top of the food the small carriage is which will support the articulation of the bust of "VIRUS" it slides on two stems and possede of the springs which gives it in initial position


I make my shock absorbers

With you always tubes out of aluminum of the round out of aluminum and within the competences of brake of door I makes four of them that I couple by two for each with dimensions

The next stage will be the assembly of the shock absorbers and the completions


Veiled with shock absorbers of washing machine which I cut into two I could make fixings of the BUST on the TRUNK



The spring of the armortissor will go in the medium and will perméttera better an elasticity of the unit


As usual the whole in corniere of 20*20 frosted of the two with dimensions ones

The coxis broke when it fell, therefore I cut out the part in question and remoulds the unit






It will be necessary that I attack myself this dimensioned there too


That passes just and does not rub on the alim of 480

 

:bounce: Here "VIRUS" in situation.


Of face




Same the bust

I GO WHEN SAME ALLEGER the WHOLE BY DRILLINGS OF LARGE DIAMETER The HEIGHT OF "VIRUS" EAST OF 640MM AND WIDTH EXT. OF The BEAMS OF 580MM


veiled the armour-plates de for the beams, protection against the shootings

Plate aluminum, frosted and curved to take the shape of the beams

 

Hello

virus will reellement have a true Web-camwood creative for the msn but especially I wanted that virus is of a new style of MOD really very different standard cases