Case Mod - In Progress Acid Veins - Cosmos S (Water Cooled, Dual Loop)

Hello to all Modders maniac, I'm new on forum and want to show You my project worklog:

code name: >> Acid Veins <<.


Main Components:

DFI DK X58-T3eH6
Intel i7 920
OCZ 6GB PC312800 CL7
HD R5850 + GeForce 9600 GT
SilverStone Strider 1000W - ST1000


WC Components:

EK Water Blocks EK-CoolStream RAD XT 240
EK Water Blocks EK-CoolStream RAD XT 360
2x Laing DDC-pump
EK-BAY Spin Res DUAL Loop - Black Acetal
"Veins" 10/13
EK Water Blocks EK-Supreme LT Acetal+Nickel
NB - EK Water Blocks EK-NB/SB 5 Acetal
EK Water Blocks EK-FC5850 Acetal + Nickel + EK Water Blocks EK-FC5850/5870 RAM Backplate - Black + EK Water Blocks EK-FC9600 SLI - Acetal VGA Block
MIPS RAM cooler 5 incl. 3 RAM Module Nickel POM Limited Edition
2l Thermochill EC-6 Clear 1000ml + Mayhems Dye


Other Components:

1x AquaComputer Aquaero
2x Lamptron Fan-Atic: 5-port
7x 120mm Enermax Magma (Green)
3x 120mm Scythe Kaze Jyuni Slip Stream 120mm Fan 1900 RPM

All closed in Cooler Master Cosmos S.

 

On the begining I want to apologise for my english, it isn't my primary language so please by tolerant, I won't be writing much instead of that I will try show more pictures.

How Cosmos S looks everyone know so I will skip showing it and start from naked pictures of case:







Hole for 240 radiator on bottom:

 

use image tags such as

Code:

[img] [/img]

around your links, saves people clicking them each time.

edit: on topic, nice cuts on the bottom

 

Rivets removed, case in pieces, many pieces ready to powder coat (black matt):










Visit in powder coat workshop:












couple minutes in furnace:



and we have it:
















OK with pictures now?

 

Off to a good start

 

Pictures are perfect now, lookin' really nice so far.

 

Putting case back together:

 

Nice rivets!!! (that's got to be geek innuendo...)
Nice thorough work, what's your plans?

 

Hmmm, it won't be anything special, visit my worklog sometimes and You will see.

Back to rivets:

 

OK time to move on, fan mode:




















Under UV light:







Few small case moddifications:

 

Really nice and clean mod my friend, the attention to detail it will pay u out at the end! Mod on!

 

This is fantastic, so are the fans, so are the LED's. Mod on!

 

This is looking great. Should be a great finish to it.


p.s. I especially like the use of plasticene!!!!! I would never have thought of thaty and probably used some expensive resin based putty and tried to dye it without sucess.......


Good work.

 

Thank You guys for good words.

Here You can see pump mod:





























And some sleeving:




























Sleeving could be better.

Cable menegment mode:
















My hands was bit shaking and its not like it should be, but it not so bad.

Switch for UV Cathodes:









Block for GeForce 9600GT to PhysX:





and after nickle plating:





Mobo I/O Backplate & GFX slots after powder coating:

 

What can I say, delicious! That's one hell of a cable management system for the 24 pin.

 

One word: Whoa

 

Looking Great Mac1as, fantastic attention to detail. Should make a great finished article

 

I will try to put it all in to case, won't be easy:








Some stuff inside:





with cables:








it wont be easy to organize it:

 

Whoa, this gets better and better!

 

I installed blocks for GPUs, MOBO & MEM: