Case Mod LIAN-LI PitStop T60 Red

[Corsaronero333]

LIAN-LI Pitstop T 60
Here we are ready for yet another adventure, well going to take 'into consideration a feast of Lian-Li.
Fasten your seatbelts
Do not smoke
prepare the popcorn
Following the beer
and .......... good vision at all
Ermanno
Let's start with posting the material, the case












Continue the presentation of the case:

[Corsaronero333]

OCZ Power Supply

Now we will examine the power supply from 750w un'OCZ that will go 'part of this mod

[Corsaronero333]

Asrock motherboard

now we move to the motherboard necessitudine staining I chose this card, fits perfectly with the mod and certainly will make 'his voice heavy lifting the cpu frequency to very high levels

[Corsaronero333]

And the adventure continues, but I'm going to submit another Harware, but rather the essential components that will dissipate the Lian-Li

We start with the arrivals from Aquatuning









We begin with the pump, is a Koolance PMP-300 is the small but pushes much

[KidMod-Southpaw]

Oh come on!?
I just had to pick my jaw up off the floor from your glass project, and now I have to get ready to do it again?

[Corsaronero333]

Now we turn to the flow, but this will be 'only visual, but there will be' a controlled dall'Aquaero xt

As I said this is only a factor esthete and will be 'enlightened, I removed the original and I placed an LED RGB LED











You guys are a step above the lines, we are speaking of red anodized aluminum passive heatsinks, small Carello of photos and for working in the next post

[KidMod-Southpaw]

This is just too cool!

[Corsaronero333]

Originally Posted by KidMod-Southpaw

Oh come on!?
I just had to pick my jaw up off the floor from your glass project, and now I have to get ready to do it again?

ahahahahahahaah thank

[Corsaronero333]

I can not put the thermometer and the fans are from Micro 40x40mm, rock 'also add the liquid of Nanoxia

[Corsaronero333]

Consider the passive heatsinks, as you see them coming, then for them to adapt to my mod I had to do some little hole

Armed with the tip of 3.25 and male M4 I am going to do one of the first working

[Corsaronero333]

Ok place, the processing of the thermometer in the upper eheheheh

Then you get a nice clean job I fitted a piece of paper tape that I put where I am going 'to cut to fit, and with a little' of sound patient I cut with the DREMEL

[Corsaronero333]

We're back to upload, today we examine the so-called shark fins term given by friends, guys here the work is long and containing many photos, I hope 'they just do not fall asleep ahahahahaha

Before processing "Aluminum" we speak of a panel dell'ACRyan satin black and a red


Working as a first line them with the 80mm nastrocarta whole area of ??work, in my experience I know 'that the only film sometimes is not enough to protect from scratches especially if using jigsaws.
Once coated is passed to the drawing or tracing on the panel, is preparing the work area (a chair with 2 planks of plywood) and the work begins

[Corsaronero333]

Here is the most 'delicate tracing of the holes of the fans are cutting and bending

Drilling ...............











And here are the twins ready for further processing










Here now we continue to place the media as the first finished work

[Corsaronero333]

Now, let us casting off, bending, it affects the side so as not to incur abnormal folds and then with a little 'tug of war .... and the fold is ready

[Corsaronero333]

Beat the fans are 40mm and see what comes out ........

[KidMod-Southpaw]

This is too much for me, so awesome!
Now stop going so fast!

[Corsaronero333]

First phase was successful, the second pass, we prepare the coating media

[Corsaronero333]

Originally Posted by KidMod-Southpaw

This is too much for me, so awesome!
Now stop going so fast!

Are you sure?
The mod is very long and impressive

[Corsaronero333]

Once assembled, we see that effect are also illuminated

[Corsaronero333]

We see a beta assembly: