1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Recent Content by andyja

  1. andyja
    Post

    Scratch Build - In Progress ⭐ Project High-ρ

    Hi mnpctech. I was not considering sending it out for a retail build. I am mainly working to start my own business designing and building...
    Post by: andyja, 15 May 2019 in forum: Project Logs
  2. andyja
    Post

    Scratch Build - In Progress ⭐ Project High-ρ

    So after using this computer for a while I decided that the acoustics needed some improvements. Basically having the pump attached to the front...
    Post by: andyja, 8 May 2019 in forum: Project Logs
  3. andyja
    Post

    Scratch Build - In Progress ⭐ Project High-ρ

    Hi All. I have completely redone my web app so you can add, move and rotate components. Resize the enclosure. The hard line water...
    Post by: andyja, 12 Apr 2019 in forum: Project Logs
  4. andyja
    Post

    Scratch Build - In Progress ⭐ Project High-ρ

    I machined Carbon Fiber side panels and a top fan trim in a water bath. TheFan trim ended up not matching the support struts in the fans as I...
    Post by: andyja, 5 Jan 2019 in forum: Project Logs
  5. andyja
    Post

    Scratch Build - In Progress ⭐ Project High-ρ

    I finally managed to get the BIOS working with the 9700k using my 8700k to update the motherboard. Set up Windows and left it running. After...
    Post by: andyja, 21 Dec 2018 in forum: Project Logs
  6. andyja
    Post

    Scratch Build - In Progress ⭐ Project High-ρ

    What a great idea to flip the block around! :idea: I have to take it all apart anyway since I need to update the BIOS to get the Z370-G...
    Post by: andyja, 11 Dec 2018 in forum: Project Logs
  7. andyja
    Post

    Scratch Build - In Progress ⭐ Project High-ρ

    Received the new 8Pin PCIe connectors but then ran out of wire so I had to get more. I really like this wire it is high strand count with silicone...
    Post by: andyja, 10 Dec 2018 in forum: Project Logs
  8. andyja
    Post

    Scratch Build - In Progress ⭐ Project High-ρ

    So I got the components for this build. CPU. Intel i7 9700k GPU Palit RTX 2080Ti Samsung 970 EVO Polaris 500GB M.2 Kingston HyperX Predator RGB...
    Post by: andyja, 4 Dec 2018 in forum: Project Logs
  9. andyja
    Post

    Scratch Build - In Progress ⭐ Project High-ρ

    Sleeved the Pump Cables. [IMG] [IMG] I did not disassemble the pump so the heat shrink does not go inside the housing just stops at the wall....
    Post by: andyja, 19 Nov 2018 in forum: Project Logs
  10. andyja
    Post

    Scratch Build - In Progress ⭐ Project High-ρ

    The rest of the cables will go behind the pannel. Thought I would try the 24 pin going directly from the board to the power supply.
    Post by: andyja, 16 Nov 2018 in forum: Project Logs
  11. andyja
    Post

    Scratch Build - In Progress ⭐ Project High-ρ

    Finished making my own 24 Pin power cable. Need to sleeve the pump cables next. [IMG] [IMG] [IMG] [IMG] [IMG] [IMG]
    Post by: andyja, 16 Nov 2018 in forum: Project Logs
  12. andyja
    Post

    Scratch Build - In Progress ⭐ Project High-ρ

    Installed front panel board. Gap at front does not look great here. Will have to see if I can fix it. [IMG] Installed fans and radiators....
    Post by: andyja, 12 Nov 2018 in forum: Project Logs
  13. andyja
    Post

    Scratch Build - In Progress ⭐ Project High-ρ

    My inspiration for the colours comes form the Bugatti Chiron. The Blue is really french racing blue. It will also have black carbon fibre side...
    Post by: andyja, 8 Nov 2018 in forum: Project Logs
  14. andyja
    Post

    Scratch Build - In Progress ⭐ Project High-ρ

    Thanks for the encouragement! I tried the belt sander on a test piece and the results were really bad. There was lots of chattering from...
    Post by: andyja, 7 Nov 2018 in forum: Project Logs
  15. andyja
    Post

    Scratch Build - In Progress ⭐ Project High-ρ

    Sheet metal parts back form powder coating. Nice light blue. [IMG] Tried to do brushed aluminium on the corner extrusions but the machining...
    Post by: andyja, 5 Nov 2018 in forum: Project Logs