Recent Content by eutronix

  1. eutronix
    Post

    Electronics 7-segment LED Clock

    Nice clock. That's quite an elegant solution you've come up with! My clock uses 8 ICs to do basically the same thing. Do you plan on making (a)...
    Post by: eutronix, 14 Aug 2008 in forum: Modding
  2. eutronix
    Post

    Electronics 7-segment LED Clock

    Well, the MAX6954 is capable of driving up to 128 discrete LEDs in one of its modes of operation. In our case, we drive 104 LEDs in our custom...
    Post by: eutronix, 30 Jul 2008 in forum: Modding
  3. eutronix
    Post

    Electronics 7-segment LED Clock

    It has a custom display we had made just for the project with several multicolored symbols and alphanumeric elements all in LEDs. It has a...
    Post by: eutronix, 29 Jul 2008 in forum: Modding
  4. eutronix
    Post

    Electronics 7-segment LED Clock

    I finally got my C-max CME8000 circuit working. So now there is no need to use their radio module. It still needs error detection and rejection...
    Post by: eutronix, 29 Jul 2008 in forum: Modding
  5. eutronix
    Post

    Electronics 7-segment LED Clock

    You could try making your own using a graphics program and its text function. Set the image to 16 x 16 pixels and adjust to just fit. You might...
    Post by: eutronix, 31 May 2008 in forum: Modding
  6. eutronix
    Post

    Electronics 7-segment LED Clock

    I called them, told them I wanted 10, they contacted C-max and e-mailed me back a few days later with a PDF quote. It was for budgetary purposes...
    Post by: eutronix, 24 May 2007 in forum: Modding
  7. eutronix
    Post

    Electronics 7-segment LED Clock

    You can get the CMA-MF-60 antenna from Digikey by special order. It costs somewhere around $1.68. If you get the bugs worked out, it is far...
    Post by: eutronix, 24 May 2007 in forum: Modding
  8. eutronix
    Post

    Electronics 7-segment LED Clock

    My clocks will hopefully cost less than $100 each too, but will have to be made in fairly large quantities to reach that goal. You are using...
    Post by: eutronix, 24 May 2007 in forum: Modding
  9. eutronix
    Post

    Electronics 7-segment LED Clock

    Depending on how much money you are willing to spend, you could have one custom made as I did. The cool thing about a custom job is you can have...
    Post by: eutronix, 24 May 2007 in forum: Modding
  10. eutronix
    Post

    Electronics 7-segment LED Clock

    My clock also has sound, but from an Oki ML22Q58. It can store a megabyte's worth of sound in it's own flash memory at up to CD quality. Stu
    Post by: eutronix, 23 Jan 2007 in forum: Modding
  11. eutronix
    Post

    Electronics 7-segment LED Clock

    My PIC-based clock keeps time now, but the C-max CME8000 still isn't working. The clock is going to use a custom made LED display, but while it...
    Post by: eutronix, 23 Jan 2007 in forum: Modding
  12. eutronix
    Post

    Electronics TS4902 using differential inputs

    Thanks. After looking at a few datasheets and checking against a board that has the IC with the +/- outputs, it looks like the + is just grounded...
    Post by: eutronix, 30 Dec 2006 in forum: Modding
  13. eutronix
    Thread

    Electronics TS4902 using differential inputs

    I am trying to amplify the signal from a device with a + and - output using an ST TS4902 speaker amplifier. The problem is I do not know what to...
    Thread by: eutronix, 28 Dec 2006, 2 replies, in forum: Modding
  14. eutronix
    Post

    Electronics Coloured PCBs? :o

    Okay. Here is a thread I found on DIY solder mask. http://www.diyaudio.com/forums/showthread.php?threadid=58229&perpage=10&pagenumber=1 Hope...
    Post by: eutronix, 23 Dec 2006 in forum: Modding