1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Recent Content by Vequalsir

  1. Vequalsir
    Post

    Modding desktop hard disk into laptop?

    did you ever get the cable working? I'm looking for the same thing. I have an advantech industrial computer that had a cable that did the...
    Post by: Vequalsir, 13 Apr 2007 in forum: Modding
  2. Vequalsir
    Post

    Electronics Combining PSU rails?

    combining the rails is not a "bad" idea. The outputs of switch mode rectifiers usually have diode isolation built into the circuit. If you want...
    Post by: Vequalsir, 23 Feb 2007 in forum: Modding
  3. Vequalsir
    Post

    Electronics Hot cap

    ~SteveG A "regulated" voltage does not mean that it is free from ripple. I do agree that the ripple after the bridge should be small. A hot...
    Post by: Vequalsir, 1 Feb 2007 in forum: Modding
  4. Vequalsir
    Post

    Electronics Hot cap

    Why not add more caps? If the Cap in question is wire across your positive and negative leads, I agree that its job in life is to reduce ripple...
    Post by: Vequalsir, 30 Jan 2007 in forum: Modding
  5. Vequalsir
    Post

    Modding Keyboard mod

    Saitek Keyboards I really like the EclipseII Boards. I found mine for $65 and love it.
    Post by: Vequalsir, 29 Jan 2007 in forum: Modding
  6. Vequalsir
    Post

    Electronics current limiting

    Check mail order places for 1/2amp fuses. There are a lot of different types out there. I use 1/8amp fuses as pilot fuses for larger devices....
    Post by: Vequalsir, 1 Aug 2006 in forum: Modding
  7. Vequalsir
    Post

    Electronics Rebuilding a notebook battery - advice needed

    do you have any information on the charge controller. many of them only require pin strapping changes to reset max charge time and number of...
    Post by: Vequalsir, 27 Jul 2006 in forum: Modding
  8. Vequalsir
    Post

    Electronics some kind of auto switch

    I have to agree. You will need to isolate the control. I would assume the ac power source is common, so if the control is not isolated it may...
    Post by: Vequalsir, 13 Jul 2006 in forum: Modding
  9. Vequalsir
    Post

    Electronics Lowering current

    it's closer to a 12W resistor. You will only be pulling 2amps for a very short time. You might be able to cheat one at less of a rating.
    Post by: Vequalsir, 23 Jun 2006 in forum: Modding
  10. Vequalsir
    Post

    Electronics RF interference question

    it's definately the deguass circuit in the TV. Nothing to worry about. You could run it to another outlet.
    Post by: Vequalsir, 23 Jun 2006 in forum: Modding
  11. Vequalsir
    Post

    Electronics Lowering current

    To boil things down a bit you have a flash module. In essence it's just a capacitive load. You need something that will at like a pre-charge...
    Post by: Vequalsir, 23 Jun 2006 in forum: Modding
  12. Vequalsir
    Post

    Electronics Lowering current

    A circuit with 6ohms of resistive load and a six volt supply is only one amp. This is calculated by using ohm's law(voltage=currentXresistance)....
    Post by: Vequalsir, 22 Jun 2006 in forum: Modding
  13. Vequalsir
    Post

    Small Form Factor Industrial computer boards

    Things are powered by an ATX connector on a passive backplane. The cpu card can be powered directly by the standard power plug used to power...
    Post by: Vequalsir, 16 May 2006 in forum: Hardware
  14. Vequalsir
    Post

    Electronics laptop screen

    you might want to look for an industrial display controller. it may have an lcd connection on it all ready for you.
    Post by: Vequalsir, 15 May 2006 in forum: Modding
  15. Vequalsir
    Post

    Small Form Factor Industrial computer boards

    I have the 500mhz one all fired up running windows XP Pro. I tried Ubuntu, but the drivers didn't load right and it ran all cluncky. I have a...
    Post by: Vequalsir, 4 May 2006 in forum: Hardware