Stared working on the pump & res base, a total remake but just a bit bigger than the 1st one i made and now has a hole for the pump instead of hiding the pump in the bottom compartment the fan was just there to hold the base up as i fitted the carbon, hole will be housing the pump
New switches fitted in working, 1st for the LED master on/off, 2nd and 3rd are for the UV lighting on/off
Thanks Bladesingerz, Ordered myself some black tights ( wife got a bit suspicious when they arrived lol) and some thin light wood to make a fan hole cover, this will go on the base of the desk near the PSU, and will eliminate the need for 120mm fan dust covers Here i have covered a old triple RAD fan extension, this will hold the 3 intake fans on the uper right side
old triple RAD fan cover cut down to a double for the lower air hole near PSU Wrapped ready for cutting The PSU and RAM Another fan cover wrapped and cut
Took some doing, but Finally worked out a way to keep the matrix LED's 14/04/2014 - Just noticed i forgot to add the fan photos, so here they are CM Jet Flows - plane black no LED's Nice to have 2 speed controllers included with the fan, 1200rpm & 1600rpm forgive the sawdust didn't look that bad without the camera flash lol removable rubber ends!, if i had not already cut the wood i would have removed the four fan ends and cut circles not squares as the fans are about the same thickness as the wood and would have looked great.
RADs and pump in place along with the new pump carbon wrap cover (RES base) Needed to extend most the fan wires, forgot to take a pic The converted triple RAD fan holder fitted to replace the wood that was there on the test build redone the sides with new wrap, the triple RAD shown here was not in the test build,
made some blocks to raise the RES a inch higher, i might get a clear pump top in the future and light it???? The tubing covering the GPU bridge can be removed, and atm its no longer on, cant decide if i like it on or of lol
New wrap added to the front, new switches and new fan controller also partially covered the blu-ray drive under the blu-ray is my drink holder (converted DVD drive) the bottom bay holds my main OS SSD drive
Ah, I've just seen the Nomination That's great, but will it matter that the projects not completed yet?
You can just about see the LEDs for the matrix cards on the sides near the volts - + buttons they can be moved around a bit but i think they look best on the sides
No it doesn't matter if it's complete yet, motm is about open projects that still have progress happening. it doesn't matter what stage your build is at
Thanks Asouter, i understand now iv had a good look at the other entries anyway, iv been doing some quick temp tests before i finish of the build, here's all my temp info for now - CPU @4.6 GPU's Core @ 1260MHz, Mem @ 1800MHz Idle temps = (This test was done after all the 3D marks and gaming) CPU = 34c GPU1 = 29c GPU2 = 30c Water Temp before RADs = 26.1 Room Temp = 22.6 FANs at lowest settings 3D Mark (default settings) did 4 tests back to back and until the temps was at the max CPU = 58c GPU1 = 44c GPU2 = 45c Water Temp before RADs = 33.3 Room Temp = 22.1 FANs at lowest settings Heaven Bench did about 3 full tests at max settings back to back and until the temps was at the max CPU = 55c GPU1 = 39c GPU2 = 40c Water Temp before RADs = 29.5 Room Temp = 21.6 FANs at lowest settings 1 hr playtime on Grid 2 (maxed out) CPU = 54c GPU1 = 42c GPU2 = 43c Water Temp before RADs = 33.1 Room Temp = 22.3 FANs at lowest settings All this was done with the fans on the lowest settings, as when im gaming without a headset i don't like the noise I will do more testing when the desk is done, but for now im more than a bit happy with the GPU temps i was hitting 85c and even up in the 90s when i was on air with the fans on 100% and that was only running at 1100MHz on the cores The OC on the cards and CPU is stable and i haven't messed with it much during this build, i could probably hit 4.8 on the CPU and possibly 1300 on the GPUs if im lucky 3D mark score was 12751
You've made really nice progress with the desk and it's looking good. If you've checked my OM thread, you'll know that I really do mean that you work fast Also laughed at the image of you arguing with your wife on getting new dust filters and how it gives you a good reason to linger in the lingerie section Darkened