1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Search Results

Search Again
Page 1 of 3
  1. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    A small update I been working on the front part of the case. I have cut a hole for a fan [IMG] This is for a 92mm sized fan. [IMG] filed...
    Post by: SP1, 22 Nov 2008 in forum: Project Logs
  2. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    Thank you.:) I don't know about days but I drilled on and off a couple of hours maybe. I only drilled those holes while I was waiting for some...
    Post by: SP1, 17 Nov 2008 in forum: Project Logs
  3. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    I started cutting with my Dremel.:dremel: [IMG] I used a reinforced disk to cut most of thy way through. [IMG] [IMG] then a thinner...
    Post by: SP1, 14 Nov 2008 in forum: Project Logs
  4. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    I have tried sanding drums but they dont work as well on thicker steel. The file I used is a ******* cut and take just a few seconds to file...
    Post by: SP1, 2 Nov 2008 in forum: Project Logs
  5. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    You are right the steel doorwas too heavy it would not work at all. That was a MicroATX case I was working on. I also made it too small and have...
    Post by: SP1, 30 Oct 2008 in forum: Project Logs
  6. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    Patience thats one way of putting it.:) I got some Dremel cutting discs and started cutting [IMG] With all that drilling it did not take long...
    Post by: SP1, 27 Oct 2008 in forum: Project Logs
  7. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    Thank you It took a long time to drill those holes by hand. [IMG] I think I will wait for those cutting discs. [IMG]
    Post by: SP1, 15 Oct 2008 in forum: Project Logs
  8. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    I have run out of cutting discs for my dremel, I can't think why?. I am waiting for some more by post. I have drilled holes for a cut out for...
    Post by: SP1, 14 Oct 2008 in forum: Project Logs
  9. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    Those are screen hinges from a laptop and they were useless. The door was made out of steel and the weight of it attached to the edge would flex...
    Post by: SP1, 11 Oct 2008 in forum: Project Logs
  10. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    I have made this case too small, I don't think I will be able to fit all I want inside. I am going to start again. I have this Lian-Li...
    Post by: SP1, 2 Oct 2008 in forum: Project Logs
  11. SP1
    Post

    Disaster Dremel 300 and flex shaft

    I have both and they fit together fine.
    Post by: SP1, 21 Sep 2008 in forum: Modding
  12. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    It has been a while since I have done some work on this case,I'm sorry. I spend most of my time working and do this in bits. I had to drill the...
    Post by: SP1, 19 Jul 2008 in forum: Project Logs
  13. SP1
    Post

    Case Mod - In Progress Project: The Arsenal - COMPLETED!!!

    Emirates is the main sponsor. Even the stadium is called the Emirates stadium.
    Post by: SP1, 26 Jun 2008 in forum: Project Logs
  14. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    You are right. Steel takes more time to cut and creates a lot noise.
    Post by: SP1, 20 Apr 2008 in forum: Project Logs
  15. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    Started cutting [IMG] [IMG] Takes more time cutting through but getting there [IMG] Thicker steel,a lot more metal dust than before the Dremel's...
    Post by: SP1, 19 Apr 2008 in forum: Project Logs
  16. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    I got another tray made but this time in 1.6mm steel. It is a lot heavier than the 1.2mm one. Started cutting the PSU hole. [IMG] [IMG] [IMG]...
    Post by: SP1, 16 Apr 2008 in forum: Project Logs
  17. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    The mother board tray won't fit so well against the back of the case. Because of the rivets I put sheet metal to fill the gaps. I glued all the...
    Post by: SP1, 13 Apr 2008 in forum: Project Logs
  18. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    [IMG] The first hole I cut I used the 409 disc.These are thin and brittle and when they are half the diameter left wear down fast. The last holes...
    Post by: SP1, 10 Apr 2008 in forum: Project Logs
  19. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    Er, I didn't think about that,I might have to use filler and sand it down. Even if I polish it it will go dull after a while. I am using...
    Post by: SP1, 7 Apr 2008 in forum: Project Logs
  20. SP1
    Post

    Scratch Build – In Progress SP1's Project.

    This bracket is for a slim DVD Writer [IMG] Drive fits perfectly [IMG] Clamped in place and drilled holes [IMG] Bolted in [IMG]
    Post by: SP1, 5 Apr 2008 in forum: Project Logs
Showing results 1 to 20 of 48 Next >
Search Again
Page 1 of 3