Asus A8N32-SLI Deluxe

i guess i'll go for the optional wifi to save on the linksys pci because I've hear that with two double slotted 7800 gtx it leaves 2 pci "x-fi and tuner" and that one slot near the cpu that's 4 the optional wifi that should all fit with proper cooling right

 

Well, does your graphics card take up two slots, or just one?

If you have only one, single slot, graphics card, then you should be able to fit three PCI cards(tuner, X-Fi, and wifi) onto the motherboard. But if you have a dual slot cooler on your graphics card, or have more then one graphics card, get the Wifi/Deluxe as opposed to the duluxe standard(stupid Asus and their stupid naming system).

 

Thanks for the warm welcome

Thanks for the warm welcome to the forums, the board was disappointing. I build alot of computers (for living and for friends and friends of the family and pretty much any other tom dick or harry that my folks might know lol
Like i said, when i put up that post i had those exact two builds, both ran amazing with stock values, the only unfortunate thing is the limiter. thats the only option asus has offered with any ram divider or ratio locker ect... im not quite sure what to do from this point as i can take the board back to my local store they said they would happily exchange the mobo as they couldnt figure out this issue... my problem is that its a watercooled box... alot of work to pull the mobo off to swap it out
Well the only appealing thing about this board was its supposed ability to run at full 16x speeds in sli mode (others reduced to 8x in sli). Im fairly sure ill be trading this board back for either the a8n sli premium or the dfi ut nf4. In either case ive had absolutely no luck with this board and i dont believe it desirves the asus stamp on it

 

Bigz? Any comments on this?

It's intresting the bamastar has had the issue twice, and I must confess I don't fully understand what he's referring to(still havn't got my mind around dividers and htt and fsb and all that jazz), but I would have thought the issue would have been picked up on on other forums that have used the board rather extensively, yet I've seen no complaints about dividers, just a few about voltage options.

 

Well heres the actual problem im having with this board, so we will run two programs to quickly check to see results - Ai Boost (shows temp speed and fsb) CPUid
Okay start up this machine fully stock and check with either fsb will show as 800 (typically this will increase with your adjustments during oc'ing). Now try that again but this time go into bios under the cpu settings into memsettings into memlock and set it for 200 (200 = ddr400) and now check the fsb ( O_O fsb now dropped to 200)
this is where im stuck at so now... i am forced to run my poor poor samsung tccd ram at about 230mhz in order to keep my fsb speeds during overclock (

 

Hmm, this obviously isn't a problem of noobyness, so it seems very strange. I feel bad saying this on bit-tech, but go here:

http://www.xtremesystems.org/forums/showthread.php?t=80491

Goto the last page and let them know. Currently thats about the most knowledable user base with regards to the A8N32-SLI, and they should be able to help you, if anyone can. Sorry I can't help more

 

that one cannot be used in comparison really can it? i mean he's running his ram at 166 (333)... Lets see that puppy put that ram back up to ddr400 then lets retry that oc. I can get my top specs as is.... 272 @11 with ram running at 197mhz (stable) but with ram forced at 200 i can get to about 230 fsb before it drops the ram to 166. ALSO need to mention id sure LOVE to see a screenshot of that machine with those settings runnin ai boost ... as it will indicate the actual bus speed... the fsb speed.... u can see on the cpuid test it DOES NOT include the actual front side bus speed for amd it does for intel btw

 

That entire threads huge, and is about the board in general, and many peoples experiences with it. Not just one guys. Goto the end of it, post your story, and hope for a solution.

 

ok if im not over clocking whats the fastest ram i can put on this mother board

 

Well, PC3200 would be the stuff you'd want for this if you're not intending on overclocking at all. Getting crucials standard PC3200 ram would be fine.

 

ok I want 2 gb of mem so for whatever reason should i get two 1 gb models or four 512 mb models and don't timings matter ? mabey i want to overclock a little hmm? and what a bout those 1gb models from crucial specialy buit for the a8n32 delux

 

I'd just like to say i have one of these mobo and have the following kit:

AMD X2 4800+ @ 2.75
2GB Corsair DDR XMS3500LL Pro
2 x 7800GTX 512 XFX XXX @ 580/1730
Scythe Ninja

whats good?: it's a rock solid overclocker
whats bad?: it was a real squeeze to get my aftermarket hs on, there is little room around the cpu. I have 2 dual slot cards and hence no more pci slots - but hey the cards are worth it.

 

newb13 care to post some screenies PLEASE include screenies of ur rams mhz and ur boards fsb (use aiboost and cpuid) cpuid will NOT show a fsb rate will only show ur rams mhz aiboost will indicate ur actual fsb speed ( please include the scrrenies from ur machine while its oc'd ) P.S. MUST see the actual fsb speed please

 

i'm at work now, will post screenies if you need them - but i can tell you i dont use that AI crap, this is manually oc'd and prime stable. The FSB is set to 250 with a multiplier of 11. Memory is on a divider 166, but enables me to run at cas 2.0 T1. If I wanted to run the memory 1-1, then i have to adjust the cas to 2.5 to get stability. So 2750, an idle temp of 46c and a stressed high temp of 56c. Not bad for air.

 

It'd probably be faster for you to run a high FSB with slacker timings (2.5 isn't that bad) as you will benefit from the increased memory bandwidth.

Post a topic in Hardware and Overclocking if you have questions like this or, even better, do a forum search. There's a wealth of information available on this issue

 

are there any other doual x16 motherboards out there? the PCI slot layout is bugging me cuz i wanna pack an x-fi card in with two double slotted bfg 7800 512's and eveyone's saying that's not possible even though there's two PCI slots right between the x16 slots so woulden't one be in the clear?

 

Alienware did it with their Aurora 7500 FX-60 system: http://www.bit-tech.net/hardware/2006/01/11/alienware_aurora7500/1.html

The system uses the A8N32-SLI Deluxe motherboard, two EVGA 7800 GTX 512 and a Creative X-Fi Fatal1ty FPS.

 

another option is to use a pci riser card or an extension cable (if you have the room in your case) - i will probably be looking at this when i need to squeeze a physics card in between my pair of 512's.

 

just use a PCIx4 slot for the PPU. no need for PCI. I think they were bringing a PCI-E version of the physics processor out...I have two NV78's on my A8n32 and theres JUST enough room for my digital TV card on the top slot. Tight fit though

 

still no screenies ... this motherboard is faulty im hoping that im wrong and someone can show me a screenie with their A8N32-SLI DELUXE BOARD showing the aiboost screen with it overclocked, very very interested to see some fsb speeds

DID this thread die on me