1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Scratch Build – In Progress " Dragon Desk" ( build in progress )

Discussion in 'Project Logs' started by Gas_designs, 3 Jul 2015.

  1. Gas_designs

    Gas_designs Member

    Joined:
    29 Sep 2014
    Posts:
    150
    Likes Received:
    1
    Today I begin to make the rear holes of the radiators, where will waste 2 :: :dremel:

    [​IMG]

    Small and simple idea, to smooth the circles :: :D

    [​IMG]

    And finally mount the radiator ::

    [​IMG]

    Now the two radiators are united, skipping the power supply, with rigid pipe, so I am created a template of the curvature :: :)

    [​IMG]

    Now I connect them with its fittings ::

    [​IMG]

    [​IMG]

    [​IMG]

    ............. :clap: :clap:
     
  2. Icelander

    Icelander Member

    Joined:
    3 Mar 2015
    Posts:
    325
    Likes Received:
    7
    slick bend around the PSU ;)
     
  3. Gas_designs

    Gas_designs Member

    Joined:
    29 Sep 2014
    Posts:
    150
    Likes Received:
    1
    Hi guys :D

    Today it mounts the grids 360mm Phobya and since the 3 fans are distant 20mm from each other, I have to make holes :: :)

    [​IMG]

    [​IMG]

    Now you have 2 buttons 25mm:: :D

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]


    ................ :dremel:
     
  4. Gas_designs

    Gas_designs Member

    Joined:
    29 Sep 2014
    Posts:
    150
    Likes Received:
    1
    In the meantime a little sleeving... :D

    [​IMG]

    Now after taking exact measurements , start to make holes for the bulkhead :: :thumb:

    [​IMG]

    [​IMG]

    [​IMG]

    Now step to the vertical panel of the mobo , even here the holes of the bulkhead , and the screen of the liquid temperature , and the window for Strix :: :dremel: :dremel:

    [​IMG]

    [​IMG]


    ..................... :thumb:
     
  5. Matrix74

    Matrix74 New Member

    Joined:
    16 Aug 2015
    Posts:
    49
    Likes Received:
    0
    beautiful buttons ......., I have to take them too but I am undecided on color and color of the LED must have.....:duh:

    I follow you

    :clap::clap::clap::clap::jawdrop::jawdrop::jawdrop::jawdrop:

    Good WORK......!!!!!
     
  6. Gas_designs

    Gas_designs Member

    Joined:
    29 Sep 2014
    Posts:
    150
    Likes Received:
    1
    Hello guys ... Today we start with a layout , to mesh power supply:: :clap:

    [​IMG]

    Once covered the area with the paper, proceed to give a nice pass from vinavil:: :thumb:

    [​IMG]

    So look 24H::*

    [​IMG]

    Now that thelayout, it is hardened for good, proceed with the 1st pass, with a little bit::*

    [​IMG]

    Then go climbing with the measures of the tips::* :thumb:

    [​IMG]

    Removed the burrs , it introduces itself:: :D

    [​IMG]

    .................... :dremel:
     
  7. Matrix74

    Matrix74 New Member

    Joined:
    16 Aug 2015
    Posts:
    49
    Likes Received:
    0
    :clap::clap::clap::clap::thumb::thumb::thumb:

    and this is the air intake in the shape of flower..............
     
  8. Gas_designs

    Gas_designs Member

    Joined:
    29 Sep 2014
    Posts:
    150
    Likes Received:
    1
    Here we are, now a chore easy easy:** :dremel:

    [​IMG]

    [​IMG]

    Aluminum thread M 4X0,7

    [​IMG]

    Allen Steel::* :D

    [​IMG]

    And finally fixed it all:**

    [​IMG]

    [​IMG]

    [​IMG]

    ................. :dremel: :dremel: :clap:
     
  9. Gas_designs

    Gas_designs Member

    Joined:
    29 Sep 2014
    Posts:
    150
    Likes Received:
    1
    Meanwhile came the sister, because she was lonely ..... :thumb:

    [​IMG]

    [​IMG]


    ................ :dremel:
     
  10. Gas_designs

    Gas_designs Member

    Joined:
    29 Sep 2014
    Posts:
    150
    Likes Received:
    1
    Now it's the most fun, position the 2 lower grilles of phobya, under the desk , in the air inlet to the radiators ...

    [​IMG]

    [​IMG]

    Now I take the imprint of the hexagons grid..... :)

    [​IMG]

    And then slowly , I take all their centers .... ready for drilling ..... :duh: :duh:

    [​IMG]

    [​IMG]

    ................. :clap:
     
  11. Icelander

    Icelander Member

    Joined:
    3 Mar 2015
    Posts:
    325
    Likes Received:
    7
    wow. have fun filing that my man :thumb::dremel:
     
  12. Gas_designs

    Gas_designs Member

    Joined:
    29 Sep 2014
    Posts:
    150
    Likes Received:
    1

    There will be fun ... :lol: :lol: :lol:
     
  13. Gas_designs

    Gas_designs Member

    Joined:
    29 Sep 2014
    Posts:
    150
    Likes Received:
    1
    Here we are guys, after a little break, because night work. :rolleyes:

    I begin the adventure of 244 holes, with a tip from 6mm to start.. :D

    [​IMG]

    Some chips ... :dremel:

    [​IMG]

    And now a nice clean.

    [​IMG]

    Now we start to make holes with a cup 16mm, with the new drill of Bosch, as my old Valex has abandoned me . :idea:

    [​IMG]


    ............... :clap: :clap: :clap:
     
  14. Gas_designs

    Gas_designs Member

    Joined:
    29 Sep 2014
    Posts:
    150
    Likes Received:
    1
    Now we begin the work more complicated, I start with a first pass with a cup 16 :dremel:

    [​IMG]

    Some cutting oil , does not hurt :)

    [​IMG]

    Chips - chips , chips and more :lol:

    [​IMG]

    And yet chips :lol:

    [​IMG]

    And after 3 hours :clap:

    [​IMG]

    A nice clean, and tomorrow will continue , with smaller holes

    [​IMG]
     
  15. ajangusjames

    ajangusjames New Member

    Joined:
    26 Dec 2011
    Posts:
    47
    Likes Received:
    0
    This looks incredible. You have my attention.
     
  16. Gas_designs

    Gas_designs Member

    Joined:
    29 Sep 2014
    Posts:
    150
    Likes Received:
    1
    Thank ajangusjames. :thumb:
     
  17. OmightyOne

    OmightyOne Member

    Joined:
    7 Nov 2011
    Posts:
    168
    Likes Received:
    7
    Very nice, jealous of all the WC parts!
     
  18. Gas_designs

    Gas_designs Member

    Joined:
    29 Sep 2014
    Posts:
    150
    Likes Received:
    1
    Hi guys .... :thumb:
    n this step , the aluminum hole , to fix any HDD 3 , and on the shelf 3 SSD :dremel:

    [​IMG]

    [​IMG]

    I put the rubber to the vibrations.

    [​IMG]

    Now it's up to ssd. :dremel:

    [​IMG]

    [​IMG]

    ........... :thumb:
     
  19. Gas_designs

    Gas_designs Member

    Joined:
    29 Sep 2014
    Posts:
    150
    Likes Received:
    1
    Fixing the grid Phobya. :thumb:

    [​IMG]

    Now the holes Laser Guide, I make a thread, and insert the allen steel. :D

    [​IMG]

    Some wing nuts. :dremel:

    [​IMG]

    Finally fixed the hatches with butterflies, so 'to be comfortable, and no tools for disassembly. :naughty:

    [​IMG]

    [​IMG]

    PS:
    A little helper for precise holes. :clap:
    [​IMG]
     
    Last edited: 12 Sep 2015
  20. Gas_designs

    Gas_designs Member

    Joined:
    29 Sep 2014
    Posts:
    150
    Likes Received:
    1
    Today day soft......then mounting radiators and fans.... :thumb:

    [​IMG]

    [​IMG]

    [​IMG]


    ........... :clap:
     

Share This Page