SketchUp Sketchup Components Collection (SCC) Discussion

Portugal , Vila Nova de Gaia

 

Ah! Vila Nova de Gaia

 

Could you guys please submit these through my website?

And anyone else got any new work?


----


I've just added three items:
http://scc.jezmckean.com/item/427
http://scc.jezmckean.com/item/428
http://scc.jezmckean.com/item/429

 

PORTUGUESE POST ONLY !!!

Maia (Porto)
ĿªЪяεġø™ por acaso não trabalhas com SolidWorks ?
Precisava de umas ideias para o meu projecto:
http://forums.bit-tech.net/showthread.php?t=167913&page=22

 

Thanks for the model Mick. Should help lots planning

 

SolidWorks ? Posso tentar , ao fim ao cabo é tudo igual nesse link já se vê potencial tens PM

 

PM desculpa a ignorancia

 

LoOL , não é PM (private message). É uma mensagem no teu perfil

 

Anyone got a acetal and copper ek supreme hf and 5870 with ek acetal and copper block? Thanks. Also how do you do mesh quickly and easily around corners and curves and stuff?

 

for holes in curves try this motas

http://sketchup.google.com/3dwarehouse/details?mid=80beaf83b56acc1e7aad1d3507922b84

 

Where can i get this radiator for my case? http://forums.bit-tech.net/showthread.php?t=167913&page=22 (SolidWorks user)

Nice work Roboduck

 

Just emailed this dual xeon board to Jez. Needed it for a folding rig rack design so thought I'd upload it too!

 

3 items added:

http://scc.jezmckean.com/item/433
http://scc.jezmckean.com/item/432
http://scc.jezmckean.com/item/431

 

Sorry I haven't checked this thread for a while. I submitted this to jezmck's site.

For now you can get if from http://www.filefront.com/16180541/MCR320.SLDPRT

 

Currently I'm designing a mainboard template after the ATX specification to have mounting holes at the right places in future projects etc.

Right now I'm trying to figure out the correct placement of the different connector slots (PCI, PCI-X, PCI-E). I'm leaving out AGP for obvious reasons.

However I can't find any ressource as where to place the PCI-E connectors. The official standards are very expensive as you have to be in some club. Kinda low for a supposedly open standard. Could anyone enlighten me with some information please?
Do you even understand what I want to know?

Edit: An example: There's a connector every .8 inches. I know where to put a PCI slot. From this I can figure out where to place the PCI-E slot in height. How far off is the connector from the side of the board though?

 

I'm a little confused, as the PDF you link to showsthe position of dimensions on Page 12 for the slots? Surely you can also confirm this by measuring a motherboard?

Regardless of what type of slot it is the physical slot will always be in the same position from the parallel edge of the board, the depth from the rear of the board could easily be measured on an existing motherboard with PCIx.

 

That's what I tried to explain, thank you. I know the position from the parallel edge of the board, but not from the rear edge.

Yeah sure you could measure the depth, but that's not what I am interested in. I want the placement (and measurement of cards) to be exact for once.

The height of mainboard coolers or caps can be measured or estimated even, but some important measurements should be correct I think, such as mounting holes for the board itself, the CPU cooler, or the expansion slots.

It would be really nice to have some correct templates for a mainboard, a PCI card and a PCI-E card (just the PCB and the mounting bracket). That way you'd only have to change the length of the card, add a texture and start adding details if you need them.

I found a pdf of the old 1.1 specification somewhere *cough* and the measurements haven't changed between 1.1 and 2.1.

 

Latest SolidWorks Creation the SilverStone Temjin SST TJ07.




PM me if you want the model or click on "My SolidWorks Stuff" in my sig.

 

Thats awesome roboduck. Anyone got an ek supreme hf model working on a case design and have everything except that.

 

Just added some great new models by Vehement