Cooling water cooling a shuttle

Discussion in 'Hardware' started by Burnout21, 28 Nov 2005.

Page 2 of 2
  1. AWACS

    AWACS What's a Dremel?

    Joined:
    10 Jun 2005
    Posts:
    371
    Likes Received:
    0
    yes...
     
    AWACS, 30 Nov 2005
    #21
  2. scotty6435

    scotty6435 What's a Dremel?

    Joined:
    4 Sep 2004
    Posts:
    1,386
    Likes Received:
    0
    Have you bought the waterblock yet? The SN41G & Sn45G use socket 478 holes so a socket A block will not fit :(
     
    scotty6435, 30 Nov 2005
    #22
  3. Burnout21

    Burnout21 Is the daddy!

    Joined:
    9 Sep 2005
    Posts:
    8,614
    Likes Received:
    197
    luckally no not yet, i noticed that it was different, didn't know it was 478 coz i dont deal with intel kit.
     
    Burnout21, 1 Dec 2005
    #23
  4. Atomic

    Atomic Gerwaff

    Joined:
    6 May 2002
    Posts:
    9,646
    Likes Received:
    94
    True, unless it uses the socket lugs to mount (like the Xice block)
     
    Atomic, 1 Dec 2005
    #24
  5. koola

    koola Minimodder

    Joined:
    11 Jul 2004
    Posts:
    2,401
    Likes Received:
    10
    koola, 1 Dec 2005
    #25
  6. Burnout21

    Burnout21 Is the daddy!

    Joined:
    9 Sep 2005
    Posts:
    8,614
    Likes Received:
    197
    Koola ur a legend! by the way is that an 80mm rad on the back? coz i sure that is exactly what i have. so i ask the question again, could i cool my XP-M 2500 just using a 80mm rad. and may be a 68gt could be pushing it a bit.
     
    Burnout21, 2 Dec 2005
    #26
  7. AWACS

    AWACS What's a Dremel?

    Joined:
    10 Jun 2005
    Posts:
    371
    Likes Received:
    0
    I think it would be pushing... you could get another one and run the some like: rez-pump-rad1-cpu-rad2-gpu-rez
    though are you going to use a rez at all? swiftech makes one that it mainly aimed towards sff use
     
    AWACS, 2 Dec 2005
    #27
  8. Burnout21

    Burnout21 Is the daddy!

    Joined:
    9 Sep 2005
    Posts:
    8,614
    Likes Received:
    197
    using a res makes life easy but may take up 2 much room. it i can find room i will use one. i was think t piece and a fill port up off that? think that makes sense? it is diffinetly a tight fit tho. could i run two rad in sequence so the same air goes threw the two rads, like fan, rad+rad,fan?
     
    Burnout21, 2 Dec 2005
    #28
  9. koola

    koola Minimodder

    Joined:
    11 Jul 2004
    Posts:
    2,401
    Likes Received:
    10
    That's pushing it a lot!

    I got highish temps with my shuttle setup, but that's because it only had a 80.1 BIM rad. If you could fit a 120.1 BIX on the back or in the Drive bay, i'm sure it would be acceptable :)
     
    koola, 2 Dec 2005
    #29
  10. sc4mpi

    sc4mpi OG watercooler

    Joined:
    16 Jan 2005
    Posts:
    625
    Likes Received:
    4
    sc4mpi, 4 Dec 2005
    #30
  11. Beavy

    Beavy What's a Dremel?

    Joined:
    3 Nov 2005
    Posts:
    14
    Likes Received:
    0
    Last edited: 29 Dec 2005
    Beavy, 20 Dec 2005
    #31
  12. AWACS

    AWACS What's a Dremel?

    Joined:
    10 Jun 2005
    Posts:
    371
    Likes Received:
    0
    it asks for login information ---> linky broken
     
    AWACS, 21 Dec 2005
    #32
  13. Atomic

    Atomic Gerwaff

    Joined:
    6 May 2002
    Posts:
    9,646
    Likes Received:
    94
    Link works fine, just that forum needs you to register before you can see anything...
     
    Atomic, 21 Dec 2005
    #33
Page 2 of 2
Tags:

Share This Page