1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Recent Content by pekcitron

  1. pekcitron
    Post

    Case Mod - In Progress NES 3.0 -nintendo pc build (Finished Build)

    Impressive! I like the selection of the hardware you have done and how you manage to put everybody in that case! Quick question, where did you get...
    Post by: pekcitron, 26 May 2015 in forum: Project Logs
  2. pekcitron
    Post

    Case Mod - In Progress Lunar - FINISH

    Really good, nice job :clap: ! I had similar idea in my mind and tried few configurations on sketchup ... you are much better than me :D !
    Post by: pekcitron, 26 May 2015 in forum: Project Logs
  3. pekcitron
    Post

    Scratch Build – In Progress Wood And Copper Computer (with NOFAN CR-95C)

    I'm thinking about removing the shroud too, but I'm not sure it will really reduce noise as the fan speed can't go slower than a minimum value...
    Post by: pekcitron, 10 May 2015 in forum: Project Logs
  4. pekcitron
    Post

    Scratch Build – In Progress Wood And Copper Computer (with NOFAN CR-95C)

    I've done some holes for the HDD and do some tests. That's better, I'm around 35°C now and the temperature react much better with the BeQuiet...
    Post by: pekcitron, 10 May 2015 in forum: Project Logs
  5. pekcitron
    Post

    Scratch Build – In Progress Wood And Copper Computer (with NOFAN CR-95C)

    Thanks :)
    Post by: pekcitron, 10 May 2015 in forum: Project Logs
  6. pekcitron
    Post

    Case Mod - In Progress Elegance by MetallicAcid

    mmmh, I vote for the acrylic moved to the inside too. You have put a lot of nice curves and, for me, putting the acrylic outside gives more...
    Post by: pekcitron, 9 May 2015 in forum: Project Logs
  7. pekcitron
    Post

    Case Mod - In Progress Elegance by MetallicAcid

    Don't know why but I didn't catch your mod on the forum and that was a big mistake! I really like the shape you give to the case and you have well...
    Post by: pekcitron, 7 May 2015 in forum: Project Logs
  8. pekcitron
    Post

    Mod of the Month Mod of the Month April 2015 in association with Corsair

    Han!!!! :blush: Thanks a lot bit-tech, I'm so happy! I couldn't expect better news for my mod! Congratulations to all modders, you have done an...
    Post by: pekcitron, 7 May 2015 in forum: Project Logs
  9. pekcitron
    Post

    Scratch Build – In Progress Wood And Copper Computer (with NOFAN CR-95C)

    New piece for the SSD. I've reverted the SSD, connectors are now at the bottom instead of top, which gives more air to cool down the HDD. I've...
    Post by: pekcitron, 6 May 2015 in forum: Project Logs
  10. pekcitron
    Post

    Scratch Build – In Progress Wood And Copper Computer (with NOFAN CR-95C)

    I'm studying to possibilities: Splitting Cable Fanless modification (will not be easy to find a good rad and temp could be too high) :D
    Post by: pekcitron, 6 May 2015 in forum: Project Logs
  11. pekcitron
    Post

    Scratch Build – In Progress Wood And Copper Computer (with NOFAN CR-95C)

    Thanks :) I've modified the GPU bios in order to reduce the min fan speed. But after flashing the modified bios it was still at the same minimum...
    Post by: pekcitron, 3 May 2015 in forum: Project Logs
  12. pekcitron
    Post

    Scratch Build – In Progress Wood And Copper Computer (with NOFAN CR-95C)

    As I told you in the previous post, I found a Speedfan configuration to link the chassis fan to the GPU load (I'm mainly using the Fan Control tab...
    Post by: pekcitron, 3 May 2015 in forum: Project Logs
  13. pekcitron
    Post

    Scratch Build – In Progress Wood And Copper Computer (with NOFAN CR-95C)

    I could finally find a Speedfan configuration which works like a charm! I've also disabled smart fan control in BIOS, don't know if it works...
    Post by: pekcitron, 3 May 2015 in forum: Project Logs
  14. pekcitron
    Post

    Case Mod - In Progress Felix: Old Soviet computer

    Impressive idea and mod! I like how you used the electrical components and how you have them repaired and enhanced. Clean job too!
    Post by: pekcitron, 3 May 2015 in forum: Project Logs
  15. pekcitron
    Post

    Scratch Build – In Progress Wood And Copper Computer (with NOFAN CR-95C)

    Glued (except the top plate), update the screws to a better look (I like torx), create 50% of the closing mechanism, mount all components and ......
    Post by: pekcitron, 26 Apr 2015 in forum: Project Logs