1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Electronics Replacing a CRT flyback transformer

Discussion in 'Modding' started by Emon, 11 Jul 2005.

  1. Emon

    Emon What's a Dremel?

    Joined:
    14 Jun 2004
    Posts:
    680
    Likes Received:
    0
    So the flyback transformer in my Samtron 75V has that annoying ringing sound. You all know it, and I want it to stop. My dad worked in TV repair shops for many years as a kid and even when he was an adult, and he was telling me that flyback transformers are designed specifically for one circuit and thus are difficult to replace. I was hoping modern CRTs use more generic designs...and that I'd be able to replace this thing. I haven't got the money for even a cheap CRT, and this one is pretty damn nice so I'd rather not trash it.

    Any ideas? How might I measure the flyback transformer's properties so I know what to replace it with?
     
  2. Emon

    Emon What's a Dremel?

    Joined:
    14 Jun 2004
    Posts:
    680
    Likes Received:
    0
    Comon, anyone?
     
  3. K.I.T.T.

    K.I.T.T. Hasselhoff™ Inside

    Joined:
    1 Jan 2005
    Posts:
    624
    Likes Received:
    1
    i personally would say its too difficult and way too dangerous to go messing in the back of a CRT especially with the flyback transformer!.....unless you love soo much you make love to it each night; dump it and pick up another even if its a cheap one till you can afford a decent one
     
  4. Emon

    Emon What's a Dremel?

    Joined:
    14 Jun 2004
    Posts:
    680
    Likes Received:
    0
    Well I'm sorry if I'm not a fan of the "buy a new one" solution. CRT danger is quite overrated...besides, my dad would be helping me, he knows a lot more about these things than I do.
     
  5. myth

    myth What's a Dremel?

    Joined:
    27 Dec 2004
    Posts:
    275
    Likes Received:
    0
    Does it have a brand name on it? model number? all you realy need is ite output and amperage :)
     
  6. Emon

    Emon What's a Dremel?

    Joined:
    14 Jun 2004
    Posts:
    680
    Likes Received:
    0
    You mean the flyback transformer? No clue actually, I've yet to open it up. My dad was just saying how they're specifically designed for circuits and hard to replace. I'm not too familiar with flyback transformers other than that they work differently from your average torodial...or so I hear...I'm not that familiar with AC.

    I'll probably take a look tomorrow. I have to replace the cable anyway, I get red/green/blue tinting (very slight) when stress is applied to certain parts of the cable...very light stress that is.
     
  7. SteveyG

    SteveyG Electromodder

    Joined:
    23 Nov 2002
    Posts:
    3,049
    Likes Received:
    8
    All you need to know is the TV make and model. That's usually how they are categorised in catalogues for replacement parts. They are relatively specific to the chassis used the TV, so you won't be able to just find a 'generic' one that will work.
     
  8. NoMercy

    NoMercy What's a Dremel?

    Joined:
    23 Nov 2004
    Posts:
    161
    Likes Received:
    0
    This question falls under the catogory of 'If you need to ask, you shouln't be doing it', if youre driven enough and want to know, find a TV repair shop willing to take you on as an apprentice, I doubt you can find people teaching HV electronics and TV repair these days :(
     
  9. Smilodon

    Smilodon The Antagonist

    Joined:
    25 Mar 2003
    Posts:
    6,244
    Likes Received:
    102
    are you sure the noise comes from the transformer itself?

    a little tip:

    try cleaning the tv inside and spray the transformer and the areas around (not on parts that becomes hot) with some clear coat. perferably something that is a bit thick and flexible.

    it's not by the book, but it can help in some cases.
     
  10. Emon

    Emon What's a Dremel?

    Joined:
    14 Jun 2004
    Posts:
    680
    Likes Received:
    0
    Pretty certain...my dad repaired TVs for years, he's always told me that was the flyback transformer.

    This isn't a "if you have to ask you shouldn't be doing it" situation. I'm not some fool that's never picked up a soldering iron before, I've just worked with CRTs only a few times. I was asking specifically how to measure a flyback transformer so I can find a suitable replacement part.
     
  11. Smilodon

    Smilodon The Antagonist

    Joined:
    25 Mar 2003
    Posts:
    6,244
    Likes Received:
    102
    i know... and CRT's aren't that dangerous if you know what you are going. (i have worked on them myself)

    you could measure resistance and inductance on the primary coil and try to calculate ow many turns and so on the transformer has, and then go from there.
     

Share This Page